Sierra Aluminum Mercury Short Filter Kit 18 7944/18 7853
Sierra Aluminum Mercury Short Filter Kit 18 7944/18 7853 . Sierra fuel water separators remove over 98.8% of emulsified water from your gasoline. Sierra's 10 micron filters are over 90% efficient at removing particles as small as 10 micron. All filters flow 90 GPH to feed even the hungriest motor. Sierra 10 micron filters are recommended. High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra s new filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 99% of emulsified water. They re engineered for today s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. Today s ethanol-blended fuels increase the chances of water in fuel tanks, resulting in premature wear, poor performance and component damage. Contaminants of over 10 micron size also can cause severe damage
Related Products
Bronze AC Motor Pump Unit 115v
Bronze AC Motor Pump Unit 115v Bronze AC Motor Pump UnitFlow rate: up to 9.6 USgpm, maximum head 40ft (17.3psi)Self-priming from dry up to 7.8ftFeatures: Easy to service and maintain.Will tolerate abrasive wear (this may affect performance - seek advice from your distributer).Handles hard and soft solids without clogging.Non pulsating flow.APPLICATIONSMARINE:Bait tank circulation, transfer oil, wash down, and utility dock pumps.INDUSTRIAL:Circulate coolant on machine tools, industrial filling systems, utility shop pump, transfer gum arabic, transfer distilled water, recharge water softeners, ice water recirculation, hydrostatic pressure testing, vacuum pump, and aspirating pump.FOOD, BEVERAGE, & DAIRY:Circulate cooling water, defrost refrigeration coils, fill drums, wash down equipment and floors, and utility pump.HOME:Fill and empty tubs and pools, empty basements, cesspools, water systems, water lawns and gardens, remove water from low areas, and recharge water softeners.PLUMBING:Empty clogged sumps, drains, sinks and tubs, and pump out water closets.FARM:Fill tractor tires, fill water tanks, pump out silo pits, liquid manures, transfer oil, and flush and clean animal pens.CONTRACTORS:Remove water from excavations, supply water to mortar boxes and cement mixing, and washdown equipment.
Seaward Products 120v Ac Water Heaters With Exchanger 6 Gallon Heater, Front Exchanger, Horizontal Orientation, 13"w 13"h 19"d, Stainless Steel Exterior
Seaward Products 120v Ac Water Heaters With Exchanger 6 Gallon Heater, Front Exchanger, Horizontal Orientation, 13"w 13"h 19"d, Stainless Steel Exterior . Heat water dockside with 120V AC power or when underway, using engine heat. These water heaters feature an ignition-protected design, cladded aluminum tanks, dual-wall heat exchangers and galvanized steel exterior. Electrical and all plumbing connections (cold/hot water in/out, engine coolant in/out, drain and pressure relief valve) are on the same side ( front ), which in most cases makes installation easier. Use of magnesium anode highly recommended for extended tank life. Material: Galvanized steel exterior; aluminum tank Port Sizes: Cold/hot in/out: 3/4" NPT, engine coolant in/out: 3/4" (for heater hose); 1/2" drain Draw: 12.5 amps 120V AC Approvals: UL approved Warranty: Two-year limited
Shurflo Extreme Series Smart Sensor Water Pumps 24v Pump, 5.7gpm, 6a/5a Draw, Sealed Variable Speed 60 Psi Pressure Switch Type, 5.0"h 5.5"w 9.25"l
Shurflo Extreme Series Smart Sensor Water Pumps 24v Pump, 5.7gpm, 6a/5a Draw, Sealed Variable Speed 60 Psi Pressure Switch Type, 5.0"h 5.5"w 9.25"l . Designed specifically for cruisers, midsize and larger yachts, these pumps incorporate a special sensor that precisely monitors your system s water pressure and adjusts the motor s speed, eliminating the need for a pressure switch and accumulator tank. They re built to thrive in the inhospitable marine environment, featuring seamless body construction and o-ring seals. The four/five chamber design and large inlet and outlet passages maximize water flow, and provide just like home showers and pump operation offshore or at the dock. The 5.7gpm pump includes two straight 1/2" hose barb quick-connect X-Fittings. Run dry without damage. Ignition protected. Self-Prime: 6' Material: Glass-reinforced nylon body and baseplate Port Sizes: 1/2" quick-connect barb, or other X-Fittings Warranty: Three years Manufacturer's Documents Installation Guidel
Shields Rubber Series 250 Shieldsflex Ii Marine Water/exhaust Hose With Wire (price Per Foot) *series Hose, 11 1/2"id, 53/64"od, 360psi Burst Pressure
Shields Rubber Series 250 Shieldsflex Ii Marine Water/exhaust Hose With Wire (price Per Foot) *series Hose, 11 1/2"id, 53/64"od, 360psi Burst Pressure . For use in all marine water and wet-exhaust applications. Designed for engine intake, bilge pump discharge, head and holding-tank connections. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Application: Engine intake, wet exhaust system, bilge pumps, scupper lines, toilet, holding tank intake/discharge Approvals: SAE J2006 Type R2 Construction: Black synthetic rubber with wire helix and HD synthetic cord Burst Strength: 870psi Temperature Range: 20 to 200 F Maximum Continuous Length: 10' or 50' (depending on Model#) *Maximum continuous length of 50'
Blue Water Marine Paint Marine Ac 70 Modified Epoxy Primer, (commercial/industrial Only) Ac70 White, Gal Kit
Blue Water Marine Paint Ac 70 Modified Epoxy Primer, (commercial/industrial Only) Ac70 White, Gal Kit . Marine AC 70 - Modified Epoxy A surface tolerant, two part 70% solids tar free epoxy anticorrosive primer. Epoxy anticorrosive coating for use on the entire vessel: Underwater, topside, deck, house, water ballast tank, cofferdam, voids, cargo holds and internal spaces.
Hand Pump Kit
Hand Pump Kit Antifreeze Hand Pump You can pump antifreeze directly into your RV water lines and supply tanks through the faucets or city water inlet with this durable RV hand pump kit. A flexible connecting line, plus city water connection and conventional water faucet adapters are included. Made in the U.S.A.
Flexible Drinking Water Tanks, 55Litre/15Gal
Flexible Drinking Water Tanks, 55Litre/15Gal Drinking water in a Vetus flexible water tank remains virtually tasteless and odorless. The fabric layers shown in picture consist of an outer wear resistant layer (1), a stretch and puncture resistant reinforcement layer (2), and a special taste-free layer (3).Easily installed, no extra parts required, just fit the nipples and connect the hosesTank assumes the shape of the space in which it is placedCan be positioned in places that are normally difficult to reachTank is able to withstand higher pressures generated by pitching and rolling - welded seams have an extra internal strip added as reinforcementIncludes: a 35mm (1-3/8") 90° fill nipple (installed at top of tank) and a 16mm (5/8") 90° outlet nipple (customer installed in desired location)
Seaward Products 120v Ac Water Heaters With Exchanger Gallon Heater, Front Exchanger, Vertical Orientation, 1/4"w 27"h 1/2"d, Stainless Steel Exterior
Seaward Products 120v Ac Water Heaters With Exchanger Gallon Heater, Front Exchanger, Vertical Orientation, 1/4"w 27"h 1/2"d, Stainless Steel Exterior . Heat water dockside with 120V AC power or when underway, using engine heat. These water heaters feature an ignition-protected design, cladded aluminum tanks, dual-wall heat exchangers and galvanized steel exterior. Electrical and all plumbing connections (cold/hot water in/out, engine coolant in/out, drain and pressure relief valve) are on the same side ( front ), which in most cases makes installation easier. Use of magnesium anode highly recommended for extended tank life. Material: Galvanized steel exterior; aluminum tank Port Sizes: Cold/hot in/out: 3/4" NPT, engine coolant in/out: 3/4" (for heater hose); 1/2" drain Draw: 12.5 amps 120V AC Approvals: UL approved Warranty: Two-year limited
Jabsco Galley Pump & Faucet Kit Only
Jabsco Galley Pump & Faucet Kit Only . An economical way to enjoy running water. The compact, quiet-running electric centrifugal pump must be mounted below water level or tank, and may be screwed directly into the tank. The attractive faucet has a stainless steel swing spout, plastic base and built-in switch. Switch rated to 5A. gpm: 1.05psi Draw: 1.6A12V DC Ports: 3/8"NPT or barb inlet; 3/8" barb outlet Dimensions: Pump: 1-13/16"H x 2-13/16"W x 4-7/8"L Warranty: One year
Hart Systems Tank Tender 4 System, 30/35 Gauge
Hart Systems Tank Tender 4 System, 30/35 Gauge . Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. Gauges read in inches for diesel and water, however, monitoring waste holding tanks is possible with optional Purge Valve Toggle Switch used to clear waste holding tank PTF tubes before taking a reading. We offer systems here for 30" deep tanks. Each system includes gauge/tank-selection panel, 30' nylon tubing per tank (continuous roll) and tank 30" penetration fittings. Panels measure 4"W x 8"H x 2-7/8"D. 3-1/16"W x 5"H cutout required. Randy Repass, the founder of West Marine, has one installed on his boat and he says "...the main reason for using Tank Tender i
Senior 4-Eyed Monster Billfish Juice Blue/Mackerel/Pink
Senior 4-Eyed Monster Billfish Juice Blue/Mackerel/Pink The newest design in the Moldcraft arsenal features outrageous smoking action and better stability in rough water. The 4-Eyed Monster Jet is available in Senior and Standard sizes, rigged and unrigged, with X-Tender tails and in all of Moldcraft?s brilliant colors Here?s lookin? at ya! Billfishjuice tablets contain highly concentrated synthetic attractants scientifically formulated to mimic natural prey rinse. These compounds dissolve at a controlled rate, and appeal to a broad range of pelagic fishes, and can dramatically increase your hookup percentages in trolling lure applications and boost the attract ability of your teasers. In controlled trials conducted in Costa Rica by the Moldcraft staff with identical teasers on both sides of the boat over 70% of the bites came to the teaser with Billfishjuice tablets. In another scientific hook bait trial conducted in Australia, strike percentages where increased by as much as 4 times. In a static demonstration at the I.G.F.A. in Dania Bch. Fl., Dr. Ben Diggles the scientist responsible for the development of the formula, sprinkled a few crumbs into a fish tank with Snook and Redfish. The fish instantly went "On Point"! Looking for the source. How many times have you raised fish into your spread and had them inspecting your best presented lures, only for them to disappear without a strike? Certainly in all but the most pristineunfished waters, a significant percentage of the fish raised into your spread do not go on to take a lure. Turning these lookers into takers can make the difference between those fishless days everyone wants to avoid and a successful outing. And of course for tournament anglers the stakes are even higher. Field testing has shown that addition of Billfish Juice tablets into your lures can increase the number of strikes from Marlin, Sailfish, Tunas, Dolphin, Wahoo, Kingfish, Cobia, Mackerels and other pelagic gamefish by over 100% compared to identical lures without attractants. In today?s world of increasing oil prices and decreasing leisure time, can YOU afford NOT to have Billfish Juice technology on the end of your line? *Click on the magnifying glass icon for skirt options.
Shields Rubber Series 250 Shieldsflex Ii Marine Water/exhaust Hose With Wire (price Per Foot) Hose, 1 5/8"id, 2"od, 320psi Burst Pressure
Shields Rubber Series 250 Shieldsflex Ii Marine Water/exhaust Hose With Wire (price Per Foot) Hose, 1 5/8"id, 2"od, 320psi Burst Pressure . For use in all marine water and wet-exhaust applications. Designed for engine intake, bilge pump discharge, head and holding-tank connections. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Application: Engine intake, wet exhaust system, bilge pumps, scupper lines, toilet, holding tank intake/discharge Approvals: SAE J2006 Type R2 Construction: Black synthetic rubber with wire helix and HD synthetic cord Burst Strength: 870psi Temperature Range: 20 to 200 F Maximum Continuous Length: 10' or 50' (depending on Model#) *Maximum continuous length of 50'
Sierra Fuel/water Separator Kits With 1/4" Alum. Long Filter, For Engine Type Under 200hp, Inlet
Sierra Fuel/water Separator Kits With 1/4" Alum. Long Filter, For Engine Type Under 200hp, Inlet . Stainless-steel or aluminum Bracket and Filter Assemblies add fuel/water separating capability to any outboard, I/O or inboard. 21 micron filters with a high pleat count. More pleats means more capacity and greater efficiency. Kits include one 18-7845 (Mercury long style) or 18-7844 (Mercury short style) filter. Will not separate 2-cycle oil from gasoline. Not for use in diesel applications. 10 Micron Technology Prevents Ethanol-Related Damage and Performance Problems Ethanol-blended fuels increase the chances of water in the fuel tank, robbing your fuel injection system of critical lubrication the fuel would otherwise provide Gunk stirred up from ethanol fuels can clog fuel injectors 10 Micron Technology removes over 99% of the water and over 90% of harmful contaminants. It guarantees proper lubrication and constant fuel flow for your fuel injection system Fuel Type: Gasoline Flow Rate:
Blue Water Marine Paint Ac80 Commercial Pure Epoxy Anticorrosive Primer Kit, White, Gal
Blue Water Marine Paint Ac80 Commercial Pure Epoxy Anticorrosive Primer Kit, White, Gal . Marine AC 80 - Pure Epoxy A surface tolerant, two part 80% solids pure epoxy anticorrosive primer. Epoxy anticorrosive coating for use on the entire vessel: Underwater, topside, deck, house, water ballast tank, cofferdam, voids, cargo holds and internal spaces. High solids epoxy.
Mk5 Universal Manual Pump Henderson Mount
Mk5 Universal Manual Pump Henderson Mount This versatile pump has many applications: bilge pump, emptying holding tanks, toilet flush, water ballast transfer, etc. It can be installed in any orientation both on and under deck or bulkhead. (Through deck or bulkhead mounting requires BP9906 Deck Plate Kit.) With 3 ft. of lift: 11 GPM 45 strokesmin; 17.5 GPM 70 strokesmin. 1- 1/2 hose connections Lightweight but robust construction in tough plastic Odor-proof, nitrile diaphragm and non-choke valves Easy access for cleaning and inspection (no tools required) Suction lift: 3 ft; discharge head: 1.5 ft. Protected diaphragm is fully enclosed Approved by Lloyds (MSA) and USCG as a lifeboat pump
